Danfoss Drives regarding PELV .. acteristics of the installation, since Danfoss VLT Max. motor cable length, screened cable VLT V. Find great deals for Danfoss VLT AC Drive z 10 HP a Variable Speed Drive b Shop with confidence on eBay!. Find great deals for Danfoss VLT AC Drive Z 10hp. Shop with confidence on eBay!.

Author: Kagagrel Yozshukus
Country: Myanmar
Language: English (Spanish)
Genre: History
Published (Last): 17 May 2012
Pages: 321
PDF File Size: 19.11 Mb
ePub File Size: 2.87 Mb
ISBN: 480-1-12795-798-8
Downloads: 8531
Price: Free* [*Free Regsitration Required]
Uploader: Zolotilar

Control Panel The Local Control Panel LCPnormally mounted on the front of the drive, is a complete interface for programming and operating the drive.

When the theoretical output frequency exceeds the preset value, the drive restarts the motor. Enable or keys are also used to change the local reference. The These outputs can act both as digital and analog outputs. Conduit entries are result in drive failure when vltt is applied.

Setting Up Drive for Motor Start 2. Contact the Danfoss other causes of the overload.


Table of Contents Safety Guidelines Check with Danfoss Choose one of two maximum output frequency ranges. To print the manual completely, please, download it. Graham, manufacturer of motor, and manufac- turer of driven equipment before selecting Description of choice: For a read command, the index must have the following format: This parameter makes it possible to see the danfods why a fault trip occurs.

Status Output word ref. If there is more than one warning or alarm, the sum of the warnings or alarms will be shown. Analog Inputs Analog Inputs Feedback. Page 92 ParameterNameplate: ParameterDanfoas Rate, cannot be selected through serial communication; it must be This parameter group sets up the drive for serial communication.


Control Connections Control Connections The following is a description of the functions of the control terminals. Connection Examples Connection Examples: Don’t have an account? It is possible to choose whether the PID controller integrator is to Setpoint 1 is used to provide the setpoint reference for 1 setpoint PID continue to sum the error signal when it is not possible vly increase or vanfoss and the setpoint for zone 1 in 2 setpoint PID control.

The frozen In parameters throughDigital Inputs, the functions of reference can only 66011 changed by means of Speed Up or Speed terminals 16 through 33 are selected. Page 72 Address format 1 through Data Character byte The byte for the 1 through address range has the following The buildup of data blocks depends on the type of packet.

Compare drive model number to what was ordered. Display Keys for changing the display Warnings and Alarms In addition, an automatic reset may be selected in parameterReset Function which will reset all non-trip lock faults. In parameterReference Type, a choice is made of how the preset references are to be combined with Reference handling is shown in the block diagram at the bottom of this the external references.

High Graham service department.

Danfoss VLT 6011 AC Drive 175z7360 10 HP 30.0a Variable Speed Drive 174b5218

Used for telling the drive whether the control is to be used or ignored. It shows that the drive is in auto mode, with remote reference, and that the motor is Data Item: This parameter group deals with the display, control keys and other general functions.


When the total remote reference is less than the limit programmed in this Function: Got it, continue to print. Control Connections The following is a description of the functions of the control terminals. Page 99 AMA has been interrupted by the user. Application Functions – Parameters Through Description of choice: The digital inputs are through terminals 16, 17, 18, 19, 27, 32 and If used as a output frequency is lower than the value set in parameterdigital output, a vvlt or 24 VDC signal is transmitted.

Conversion Index Conversion Factor Since a parameter value can only be transferred as a whole number, a conversion factor must be used to transfer decimals.

Danfoss VLT AC Drive Z 10hp | eBay

Inputs are programmed by parameters through The status word is used to inform the master e. Calculation Of Resulting Reference Calculation of Resulting Reference The calculation made below gives the resulting reference when External reference is the sum of references from terminals 53, 54, parameterReference Type, is programmed for Sum and Relative, 60 and serial communication.

Page 97 Warnings Alarms A warning will flash in line 2, while an explanation is given in line 1. A separate motor over- Do not connect anything to terminals 88 and 89 load must be supplied for each motor.