The manual is embedded in the build instructions for the various Align kits. This appears to come out of the manual. At least its identical to. i have just ordered an Align 3gx flybarless control unit but i can’t find any instructions online anywhere as i like to usually download and print. Align 3Gx flybarless setup problem Electric Heli Talk. Registered User Without the 3Gx module in place, with servos connected directly to.

Author: Damuro Guktilar
Country: Mongolia
Language: English (Spanish)
Genre: Health and Food
Published (Last): 22 March 2004
Pages: 414
PDF File Size: 14.88 Mb
ePub File Size: 18.22 Mb
ISBN: 658-2-88811-946-8
Downloads: 34242
Price: Free* [*Free Regsitration Required]
Uploader: Narr

The caution at or near the bottom of the page tell you that you may to re-map the channels 3 to PIT instead of to THRO and therefore the manual is not incorrect. This completes the rudder endpoint limit adjustment for the right side.

The control unit will determine the CCPM mixing ratio or traditional mechanical mixing maximum elevator endpoints. Mznual frame rate must be selected based on your servo’s specifications. Custom parameters have been opened up in 3GX to allow pilots to fine tune nanual settings for swashplate and rudder.

If ava ilable, ensure the following functions are disabled in the transmitter: Originally Posted by Tulo I mean like if you get a e super combo new, it comes with the connection wires?

Align 3gx pdf manual | Model Flying

alitn The good news is if its a Futaba S-bus receiver then it is capable of using s-bus and one wire to control the lot. Anything else I should try, please, before telling the vendor that the unit’s bad? Introduction Brand new redesigned 3GX represents a new generation of multi function flybarless system.


The trim must be zero when using 3GX, and should not be adjusted at anytime. Graphical illustrated instruction on the computer setup software directs the user through 3ggx step by step setup process, allowing for quick setups without omitting any steps.

Gyro gain For radio with built in gyro gain settings, gain can be adjusted directly. This completes the swashplate mixing type recognization process. In addition to transmitter, the anti-torque compensation feature can also be set through 3GX interface’s rudder parameter.

3GX Flybarless System – Introduction – Align

Microbeast or 3GX aalign Flybarless setup. Press the SET button to enter A. Setting swashplate acceleration may increase the burst amp draw of servos. I personally would set it up using the newest software on aligns site Version 1. For tail pitch adjustment, center the rudder servo by either setting the 3GX flybarless to normal rate mode non-heading lockor press and hold the SET button for 2 seconds. Support with APS gyro system and bring up more functions for your helicopter.

3tx At first I thought I had a bad servo, but when I reconnected everything directly to the receiver it worked fine, so I’m thinking it must be the 3Gx unit. Tail pitch adjustment First check how the rudder responds to Tx. Should any changes made to the endpoints or subtrims on the transmitter in the future, the 3GX flybarless system initial setup must be performed again.


With 3GX in operation mode, push rudder to left or right, and press the SET button for about a second. If that doesnt work call the vendor. Adjust the maximum collective pitch using the transmitter’s swashplate mixing function pitch swash AFR.

My servos are Align DS Align 3GX version 2. Check that there is no binding throughout the pitch range.

Align 3gx pdf manual

The more dampening effect, the smoother helicopter flies, but feels less direct. Release the button before the flash sequence complete, the DIR green LED will 3bx up indicating the 3GX has been bypassed for mechanical neutral and travel range setup.

Adjust the servo neutral point and main blade pitch. In addition, the 3GX can support all of the CCPM swashplate system currently on the market including 90, and degrees swashplates. Originally Posted by Tulo What software??